Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer

Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer

YOU
SAVE US $4.17

  • Original PriceUS$14.16piece
  • SAVEUS $4.17piece
  • Discount PriceUS$9.99piece
  • ShippingFree Shipping
  • Product Rating7232

Ordering for a Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer with cheap price? Read about features, types, and other must-know topics in our Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer buying guide to make an informed choice. Buy greatest Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer Look for the Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer package that is greatest for you. Make a price comparison, discount promo, or free shipping before shopping.

- CNC Shield Board

Version: 3.0
Color: Red
Size(L*W*H): 68 x 53 x 18 mm
Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)

Features:
1. Uses removable A4988 or DRV8825 compatible stepper drivers.
2. The extension board can be used for carving machine, 3 d printer driver expansion board
3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino-UNO that turns G-code commands into stepper signals)
4. PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
6. Please note that this is an unassembled kit and Basic soldering skills are needed.

- A4988 Stepper Motor Driver

Color: Red
Size(L*W*H): 20 x 15 x 10 mm
Thermal shutdown circuitry: Yes
Crossover-current protection: Yes
Ground fault protection: Yes
Load short-circuit protection: Yes
Compatible logic supply: 3.3V and 5 V
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16

Features:
1. Mix with slow current decay modes.
2. Internal UVLO and Low RDS (On) Output.
3. Automatic current decay mode detection/selection.
4. Synchronous rectification for low power dissipation.
5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver.

- Uno R3 Board

MCU: ATmega328
Clock speed: 16 MHz
USB interface: ATmega16U2
Operating voltage: 5 V
I-I / O pin output current: 40 mA max
3.3 V output current: 150 mA max
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
EEPROM: 1 kB
Static RAM (SRAM): 2 kB
Flash memory: 32 kB
Size(L*W*H): 68 x 53 x 10 mm

Click to download universal course

Package included:

1 x Uno
-R3 Board
1 x CNC Shield Board
4 x A4988 Stepper Motor Driver
4 x Heat Sink
1 x USB Cable
1 x 40-Pin Row Needles





Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer,Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer,Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer,Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer,Geekcreit® CNC Shield UNO-R3 Board 4xA4988 Driver Kit With Heat Sink For Arduino Engraver 3D Printer
Feedback
We would be very grateful to leave you some comments when you receive your article. We do our best to provide the best possible service, but if for any reason you are unhappy with something, please contact us before leaving a negative answer and we will do our best to solve your problem.

MERCI DE CHOISIR D'ACHETER AVEC NOUS